<?xml version="1.0"?>
<html>
<body>
<h1 >Logging in the library and the daemon</h1>
<p>Libvirt includes logging facilities starting from version 0.6.0,
this complements the <a href="errors.html">error handling</a>
mechanism and APIs to allow tracing though the execution of the
library as well as in the libvirtd daemon.</p>
<p>The logging functionalities in libvirt are based on 3 key concepts,
similar to the one present in other generic logging facilities like
log4j:</p>
<ul>
<li>log messages: they are information generated at runtime by
the libvirt code, it includes a priority level (DEBUG = 1,
INFO = 2, WARNING = 3, ERROR = 4), a category, function name and
line number, indicating where it originated from, and finally
a formatted message, in addition the library adds a timestamp
at the begining of the message</li>
<li>log filters: it's a set of patter and priorities allowing to acept
or reject a log message, if the message category matches a filter,
the message priority is compared to the filter priority, if lower
the message is discarded, if higher the message is output. If
no filter matches, then a general priority level is applied to
all remaining messages. This allows to capture for example all
debug messages for the QEmu driver, but otherwise only allow
errors to show up from other parts</li>
<li>log outputs: once a message has gone though filtering a set of
output defines where to send the message, they can also filter
based on the priority, for example it may be useful to output
all messages to a debugging file but only allow errors to be
logged though syslog.</li>
</ul>
<p>The library configuration of logging is though 3 environment variables
allowing to control the logging behaviour:</p>
<ul>
<li>LIBVIRT_DEBUG: it can take the four following values:
<ul>
<li>1 or "debug": asking the library to log every message emitted,
though the filters can be used to avoid filling up the output</li>
<li>2 or "info": log all non-debugging informations</li>
<li>3 or "warn": log warnings and errors, that's the default value</li>
<li>4 or "error": log only error messages</li>
</ul></li>
<li>LIBVIRT_LOG_FILTERS: allow to define logging filters</li>
<li>LIBVIRT_LOG_OUTPUTS: allow to define logging outputs</li>
</ul>
<p>Note that, for example, setting LIBVIRT_DEBUG= is the same as unset. If
you specify an invalid value, it will be ignored with a warning. If you
have an error in a filter or output string, some of the settings may be
applied up to the point at which libvirt encountered the error.</p>
<p>Similary the daemon logging behaviour can be tuned using 3 config
variables, stored in the configuration file:
<ul>
<li>log_level: accepts the following values:
<ul>
<li>4: only errors</li>
<li>3: warnings and errors</li>
<li>2: informations, warnings and errors</li>
<li>1: debug and everything</li>
</ul></li>
<li>log_filters: allow to define logging filters</li>
<li>log_outputs: allow to define logging outputs</li>
</ul>
<p>When starting the libvirt daemon, any logging environment variable
settings will override settings in the config file. Command line options
take precedence over all. If no outputs are defined for libvirtd, it
defaults to logging to syslog when it is running as a daemon, or to
stderr when it is running in the foreground.</p>
<p>Libvirtd does not reload its logging configuration when issued a SIGHUP.
If you want to reload the configuration, you must do a <code>service
libvirtd restart</code> or manually stop and restart the daemon
yourself.</p>
<p>The syntax for filters and outputs is the same for both types of
variables.</p>
<p>The format for a filter is:</p>
<pre>x:name</pre>
<p>where <code>name</code> is a match string e.g. <code>remote</code> or
<code>qemu</code> and the x is the minimal level where matching messages
should be logged:</p>
<ul>
<li>1: DEBUG</li>
<li>2: INFO</li>
<li>3: WARNING</li>
<li>4: ERROR</li>
</ul>
<p>Multiple filters can be defined in a single string, they just need to be
separated by spaces, e.g: <code>"3:remote 4:event"</code> to only get
warning or errors from the remote layer and only errors from the event
layer.<p>
<p>If you specify a log priority in a filter that is below the default log
priority level, messages that match that filter will still be logged,
while others will not. In order to see those messages, you must also have
an output defined that includes the priority level of your filter.</p>
<p>The format for an output can be one of those 3 forms:</p>
<ul>
<li><code>x:stderr</code> output goes to stderr</li>
<li><code>x:syslog:name</code> use syslog for the output and use the
given <code>name</code> as the ident</li>
<li><code>x:file:file_path</code>output to a file, with the given
filepath</li>
</ul>
<p>In all cases the x prefix is the minimal level, acting as a filter:</p>
<ul>
<li>1: DEBUG</li>
<li>2: INFO</li>
<li>3: WARNING</li>
<li>4: ERROR</li>
</ul>
<p>Multiple output can be defined , they just need to be separated by
spaces, e.g.: <code>"3:syslog:libvirtd 1:file:/tmp/libvirt.log"</code>
will log all warnings and errors to syslog under the libvirtd ident
but also log everything debugging and informations included in the
file <code>/tmp/libvirt.log</code></p>
<p>For example setting up the following:</p>
<pre>export LIBVIRT_DEBUG=1
export LIBVIRT_LOG_OUTPUTS="1:file:virsh.log"</pre>
<p>and then running virsh will accumulate the logs in the
<code>virsh.log</code> file in a way similar to:</p>
<pre>14:29:04.771: debug : virInitialize:278 : register drivers
14:29:04.771: debug : virRegisterDriver:618 : registering Test as driver 0</pre>
<p>the messages are timestamped, there is also the level recorded,
if debug the name of the function is also printed and then the formatted
message. This should be sufficient to at least get a precise idea of
what is happening and where things are going wrong, allowing to then
put the correct breakpoints when running under a debugger.</p>
</body>
</html>
